Angle Plier for Band Setting
The Angle Plier is a slim orthodontic working plier engineered to seat and secure orthodontic bands during fitting. Symmetric pyramidal tips meet at a fine point that grips the band margin firmly without crushing or distorting the metal, giving the operator precise control over band seating and positioning before cementation. Manufactured in autoclavable stainless steel with a slim teardrop handle, the Angle Plier maintains tight hinge action and a dependable working edge over repeated sterilisation cycles. Equate Instruments supplies it non-sterile so the clinic can integrate it into its preferred steam-sterilisation workflow alongside the rest of the orthodontic plier set.
Specifications
MaterialStainless SteelRusting PreventionPassivatedUltrasonic CleanedYesUsageLeft Hand or Right HandSterileNoReusableYesTests PerformedShape Test, Boil Test and Performance TestLatex FreeYesPackingIndividually PackedQc PassedYesRelated Products
Band Seating Plier - 2.8 mm Tip
The Band Seating Plier is an orthodontic positioning plier built to seat molar bands accurately onto the tooth during fitting. A 2.8 mm carbide seating tip on the upper beak presses on the buccal or lingual band margin, while the flat opposing beak rests on the archwire or occlusal surface as an anchor point, giving the clinician controlled downward seating force without patient bite loading. Rated for use alongside archwires up to 0.50 mm (0.020 inch), the plier suits routine band placement during comprehensive orthodontic treatment. Long curved stainless-steel handles reduce pinch effort, and the instrument is autoclavable and supplied non-sterile. From Equate Instruments, it is a chairside staple for band fitting visits.
View
Dental Measuring Ruler 10 cm
The Dental Measuring Ruler 10 cm is a slim stainless-steel scale used chairside to measure paper points, gutta-percha cones, K-files and orthodontic wire with single-hand control. Millimetre and half-millimetre graduations are etched into the surface, giving a reliable reference for working-length measurement and malocclusion assessment. The rigid stainless-steel body resists bending under normal use and remains accurate over many autoclave cycles. The small top hole allows the ruler to hang from a tray hook or lanyard when not in use. Supplied non-sterile, it is a practical chairside measuring tool in the Equate Instruments range.
View
Dental Measuring Ruler 15 cm
The Dental Measuring Ruler 15 cm is a slim stainless-steel scale used chairside to measure paper points, gutta-percha cones, K-files and orthodontic wire with single-hand control. The longer 15 cm length extends to the full span of a long-file working length or a facial-arch wire segment, while the etched millimetre and half-millimetre graduations remain legible after repeated autoclaving. The rigid stainless-steel body resists bending in routine use, and a hanging hole at the top lets the ruler sit on a tray hook between cases. Supplied non-sterile, it is the longer chairside companion to the 10 cm ruler in the Equate Instruments range.
View
Deluxe Boley Gauge
The Deluxe Boley Gauge is a precision stainless-steel dental caliper calibrated in millimetres for measuring tooth widths, crown heights, prosthetic teeth and orthodontic study models. The pointed sliding jaw reads against the main scale from 0 to 80 mm, while a vernier track on the auxiliary jaw adds fine tenth-millimetre resolution for close work. Fabricated from hardened stainless steel by Equate Instruments, the gauge holds its calibration through repeated autoclave cycles and routine chemical disinfection. The pointed tips reach into interproximal contacts and embrasures where standard rulers cannot.
View
Vernier Dental Caliper 130mm
This dental caliper is a precision measuring instrument used to gauge tooth widths, arch-form dimensions, wax patterns, and study-model landmarks. The scale reads directly in millimetres so the clinician can capture accurate linear measurements chairside or on the bench during case planning and fabrication. Crafted in stainless steel with a fully autoclavable body, this Equate Instruments caliper is built for daily reuse across restorative, prosthodontic, and orthodontic workflows. Supplied non-sterile, it is ready for routine in-clinic sterilisation between measurements.
View
Boley Dental Caliper 145mm
This dental caliper is a precision measuring instrument used to gauge tooth widths, arch-form dimensions, wax patterns, and study-model landmarks. The scale reads directly in millimetres so the clinician can capture accurate linear measurements chairside or on the bench during case planning and fabrication. Crafted in stainless steel with a fully autoclavable body, this Equate Instruments caliper is built for daily reuse across restorative, prosthodontic, and orthodontic workflows. Supplied non-sterile, it is ready for routine in-clinic sterilisation between measurements.
View
Dental Caliper 0-90 mm
This dental caliper is engineered for accurate linear measurement of teeth, restorations, and stone models. The stainless-steel shaft carries a clearly etched scale graduated from zero to ninety millimetres, and a knurled thumb-screw collar locks the sliding indicator at the measured position. A short offset reference beak at the tip lets the clinician register a stable contact point on the working surface. Built from corrosion-resistant stainless steel and fully autoclavable, this caliper is a trusted daily measurement tool for orthodontists, prosthodontists, and dental technicians. Equate Instruments supplies it non-sterile for the clinic's preferred sterilisation workflow.
View
Iwanson Caliper for Wax 10 mm
The Iwanson spring caliper is a precision instrument used by dental technicians and prosthodontists to measure the thickness of wax patterns, metal copings, ceramic build-ups and thin sheet materials. The sprung arms follow the contour of the work piece, and the curved jaws close onto the measurement point while the scale reads directly on the arc from 0 to 10 mm. Crafted by Equate Instruments from stainless steel for stable spring tension, the caliper is autoclavable and tolerates routine lab solvents. A 1/10 mm track supports tenth-millimetre resolution for crown thickness checks.
View
How Utility Plier 3.2mm Max 0.028 Inch Wire
The How Utility Plier is a general-purpose orthodontic instrument for grasping, contouring and bending arch wires, as well as seating molar bands and loosely crimping crowns. Tapered parallel tips give the clinician fine control over wire positioning, and the plier will hold round or rectangular archwires up to 0.028 inch (0.71 mm) in diameter. Forged from stainless steel with a simple spring-return handle, this Equate Instruments plier is fully autoclavable and supplied non-sterile for in-clinic sterilisation between patients.
View
Bracket Positioning Tweezer 12 cm
The Bracket Positioning Tweezer is a 12 cm stainless-steel orthodontic tweezer designed to pick up, orient, and seat brackets during direct-bonding procedures. A fine hooked notch at the working tip engages the bracket slot or tie-wing and holds the bracket firmly while the clinician seats the adhesive base on the tooth surface and fine-tunes the mesiodistal and vertical position before cure. The shanks are fully satin-finished to reduce glare under the operating light and the grip zone is contoured for precise fingertip control. Equate Instruments supplies this tweezer non-sterile in autoclavable stainless steel for routine in-clinic sterilisation alongside the rest of the bonding setup.
View
Hard Wire Cutter Plier 15 Degree Tungsten-Carbide Max 0.028 Inch Wire
This Hard Wire Cutter Plier is an orthodontic cutting instrument with 15-degree angled tungsten-carbide inserts on the cutting edges. The angled head lets the clinician position the cut flush against the buccal tube or bracket, and the tungsten-carbide tips retain their edge through repeated cuts on hardened stainless-steel and beta-titanium archwires up to 0.028 inch (0.71 mm). Forged from stainless steel with a spring-return handle, this Equate Instruments plier is fully autoclavable and supplied non-sterile for in-clinic processing.
View
Orthodontic Bracket Height Gauge with 3.5, 4.0, 4.5 and 5.0 mm Arms
This Orthodontic Bracket Height Gauge is a four-arm calibrated instrument for measuring and positioning orthodontic brackets on the tooth crown. Each arm is stamped with a different reference height - 3.5, 4.0, 4.5 and 5.0 mm - so the clinician can rotate the gauge to select the appropriate vertical position for each tooth type. Machined from stainless steel with a thin, lightweight cross body, this Equate Instruments gauge is fully autoclavable and supplied non-sterile for routine in-clinic processing.
View
