Dental Caliper 0-90 mm
This dental caliper is engineered for accurate linear measurement of teeth, restorations, and stone models. The stainless-steel shaft carries a clearly etched scale graduated from zero to ninety millimetres, and a knurled thumb-screw collar locks the sliding indicator at the measured position. A short offset reference beak at the tip lets the clinician register a stable contact point on the working surface. Built from corrosion-resistant stainless steel and fully autoclavable, this caliper is a trusted daily measurement tool for orthodontists, prosthodontists, and dental technicians. Equate Instruments supplies it non-sterile for the clinic's preferred sterilisation workflow.
Specifications
MaterialStainless SteelRusting PreventionPassivatedUltrasonic CleanedYesUsageLeft Hand or Right HandSterileNoReusableYesTests PerformedShape Test, Boil Test and Performance TestLatex FreeYesPackingIndividually PackedQc PassedYesRelated Products
Deluxe Boley Gauge
The Deluxe Boley Gauge is a precision stainless-steel dental caliper calibrated in millimetres for measuring tooth widths, crown heights, prosthetic teeth and orthodontic study models. The pointed sliding jaw reads against the main scale from 0 to 80 mm, while a vernier track on the auxiliary jaw adds fine tenth-millimetre resolution for close work. Fabricated from hardened stainless steel by Equate Instruments, the gauge holds its calibration through repeated autoclave cycles and routine chemical disinfection. The pointed tips reach into interproximal contacts and embrasures where standard rulers cannot.
View
Boley Dental Caliper 145mm
This dental caliper is a precision measuring instrument used to gauge tooth widths, arch-form dimensions, wax patterns, and study-model landmarks. The scale reads directly in millimetres so the clinician can capture accurate linear measurements chairside or on the bench during case planning and fabrication. Crafted in stainless steel with a fully autoclavable body, this Equate Instruments caliper is built for daily reuse across restorative, prosthodontic, and orthodontic workflows. Supplied non-sterile, it is ready for routine in-clinic sterilisation between measurements.
View
Straight Dental Caliper 0-40 mm
The Straight Dental Caliper is a two-arm measuring instrument with a 0 to 40 mm curved arc scale for tooth and model measurements in orthodontic, prosthodontic and dental-laboratory workflows. The sharp pointed tips close precisely for gauging tooth width, crown height and intercuspal distances, while the knurled thumbscrew at the pivot locks the reading so the measurement can be transferred to a chart or model. The all stainless-steel body is polished for corrosion resistance and easy cleaning. Equate Instruments supplies the caliper non-sterile for in-clinic steam sterilisation or surface disinfection before use.
View
Flat Sliding Dental Caliper 130 mm
The Flat Sliding Dental Caliper is a measurement gauge used to record tooth width, arch dimensions, and impression details with 1 mm resolution on a 130 mm scale. The fixed jaw and the sliding jaw each carry a short L-shaped measuring foot that projects perpendicular to the ruler face, letting the operator capture inter-dental or mesio-distal distances directly on study models or in the mouth. A knurled thumb-screw locks the sliding jaw at the chosen reading so the caliper can be withdrawn from the measurement field without losing the value. The stainless steel body is fully autoclavable, and the clearly etched metric scale resists wear. Supplied non-sterile by Equate Instruments for routine in-clinic steam sterilisation.
View
Dental Caliper 0-80 mm
This dental caliper is engineered for accurate linear measurement of teeth, restorations, and stone models. The stainless-steel shaft carries a clearly etched scale graduated in millimetres, and a knurled thumb-screw collar locks the sliding indicator at the measured position. A short offset reference beak at the tip lets the clinician register a stable contact point on the working surface. Built from corrosion-resistant stainless steel and fully autoclavable, this caliper is a trusted daily measurement tool for orthodontists, prosthodontists, and dental technicians. Equate Instruments supplies it non-sterile for the clinic's preferred sterilisation workflow.
View
Boley Gauge
The Boley Gauge is a sliding-jaw caliper with a millimetre scale along the measuring beam, used in orthodontics for tooth-width measurements, Bolton analysis, and arch-length planning. The sliding head rides on a knurled thumb-wheel for fine control and locks to read a fixed dimension, while the jaws are shaped to meet flush against the mesial and distal contact points of a tooth on the cast or in the mouth. Equate Instruments manufactures the gauge in passivated stainless steel with a clearly etched scale. It is reusable and fully autoclavable, supporting routine diagnostic and treatment-planning workflows.
View
Breene Donk Gauge - Single End
The Breene Donk Gauge is a precision single-end measuring instrument designed for orthodontic and prosthodontic tooth-width assessment. A sliding jaw travels along a graduated stainless-steel bar, while the fixed and moveable arms terminate in fine pointed tips that register mesio-distal dimensions, pontic spaces, and interproximal clearances without slipping off enamel. Machined from hardened stainless steel and finished with a laser-etched millimetre scale, this Equate Instruments gauge delivers consistent readings for arch-length, tooth-dimension, and space-analysis workflows during diagnostic set-ups. Fully autoclavable and supplied non-sterile so the clinic can reprocess it in pouches or instrument cassettes.
View
Dental Measuring Ruler 10 cm
The Dental Measuring Ruler 10 cm is a slim stainless-steel scale used chairside to measure paper points, gutta-percha cones, K-files and orthodontic wire with single-hand control. Millimetre and half-millimetre graduations are etched into the surface, giving a reliable reference for working-length measurement and malocclusion assessment. The rigid stainless-steel body resists bending under normal use and remains accurate over many autoclave cycles. The small top hole allows the ruler to hang from a tray hook or lanyard when not in use. Supplied non-sterile, it is a practical chairside measuring tool in the Equate Instruments range.
View
Dental Measuring Ruler 15 cm
The Dental Measuring Ruler 15 cm is a slim stainless-steel scale used chairside to measure paper points, gutta-percha cones, K-files and orthodontic wire with single-hand control. The longer 15 cm length extends to the full span of a long-file working length or a facial-arch wire segment, while the etched millimetre and half-millimetre graduations remain legible after repeated autoclaving. The rigid stainless-steel body resists bending in routine use, and a hanging hole at the top lets the ruler sit on a tray hook between cases. Supplied non-sterile, it is the longer chairside companion to the 10 cm ruler in the Equate Instruments range.
View
Vernier Dental Caliper 130mm
This dental caliper is a precision measuring instrument used to gauge tooth widths, arch-form dimensions, wax patterns, and study-model landmarks. The scale reads directly in millimetres so the clinician can capture accurate linear measurements chairside or on the bench during case planning and fabrication. Crafted in stainless steel with a fully autoclavable body, this Equate Instruments caliper is built for daily reuse across restorative, prosthodontic, and orthodontic workflows. Supplied non-sterile, it is ready for routine in-clinic sterilisation between measurements.
View
Iwanson Caliper for Wax 10 mm
The Iwanson spring caliper is a precision instrument used by dental technicians and prosthodontists to measure the thickness of wax patterns, metal copings, ceramic build-ups and thin sheet materials. The sprung arms follow the contour of the work piece, and the curved jaws close onto the measurement point while the scale reads directly on the arc from 0 to 10 mm. Crafted by Equate Instruments from stainless steel for stable spring tension, the caliper is autoclavable and tolerates routine lab solvents. A 1/10 mm track supports tenth-millimetre resolution for crown thickness checks.
View
Dental Measuring Ruler 0-60mm
The dental measuring ruler is a thin, rigid stainless-steel blade etched with graduated millimetre markings along its working edge, giving clinicians a quick reference for intraoral and extraoral dimensional checks, including implant-site assessment, cast measurements, and radiographic references. Its low profile slips into tight working spaces without distorting soft tissue or interfering with adjacent structures. The polished surface stays legible across repeated sterilisation cycles, and the instrument is fully autoclavable. Supplied non-sterile by Equate Instruments for in-office steam processing in pouches or cassettes.
View
